Narrow Pitch (Board to FPC) Connectors: F4S Specifications

  • Sales
  • Support
  • Product Catalog
  • Downloads
Part discontinuation notice...
Discontinued part numbers

AXT518124, AXT618124, AXT538124, AXT638124, AXT546124, AXT646124, AXT5E1826, AXT6E1826, AXT5E3826, AXT6E3826, AXT5E4626, AXT6E4626

  • Last time to buy: September, 2013
Narrow Pitch (Board to FPC) Connectors F4S

Specifications for this product appear below.

Characteristics

ItemSpecificationsConditions
Electrical
characteristics
Rated current 0.3A/contact
(Max. 5 A at total contacts)
 
Rated voltage AC, DC60V  
Breakdown
voltage
150V AC for 1 min. No short-circuiting or damage at a
detection current of 1 mA when the
specified voltage is applied for one minute.
Insulation
resistance
Min. 1,000Mohm(Initial) Using 250V DC megger
(applied for 1 min.)
Contact
resistance
Max. 90mohm Measure it using HP4338B based
on the contact resistance
measurement method specified
by JIS C 5402.
Mechanical
characteristics
Composite
insertion force
Max. 0.981N/contacts × contacts
(initial)
 
Composite
removal force
Min. 0.165N/contacts × contacts  
Contact holding
force
(Socket contact)
Min. 0.49N/contacts Measure the maximum load each
contact can withstand without
being removed in the axis direction.
Environmental
characteristics
Ambient
temperature
-55°C to +85°C No freezing at low temperatures. No
dew condensation.
Soldering heat resistance Peak temperature: 260°C or less
(on the surface of the PC board
around the connector terminals)
Infrared reflow soldering
300°C within 5 sec, 350°C within 3 sec. Soldering iron
Storage temperature -55°C to +85°C (Product only)
-40°C to +50°C (emboss packing)/td>
No freezing at low temperatures.
No dew condensation.
Thermal shock
resistance
(header and
socket mated)
5 cycles,
insulation resistance min.
100Mohm,
contact resistance max.
90mohm
Sequence
1. -550-3°C, 30 minutes
2. ~, Max. 5 minutes
3. 85+30°C, 30 minutes
4. ~, Max. 5 minutes
Humidity
resistance
(header and
socket mated)
120 hours,
insulation resistance min.
100Mohm,
contact resistance max.
90mohm
Bath temperature 40±2°C,
humidity 90 to 95% R.H.
Saltwater spray
resistance
(header and
socket mated)
24 hours,
insulation resistance min.
100Mohm,
contact resistance max.
90mohm
Bath temperature 35±2°C,
saltwater concentration 5±1%
H2S resistance
(header and
socket mated)
48 hours,
contact resistance max.
90mohm
Bath temperature 40±2°C,
gas concentration 3±1 ppm,
humidity 75 to 80% R.H.
Lifetime
characteristics
Insertion and
removal life
50 times epeated insertion and removal
speed of max. 200 times/hours
Unit weight 50-contacts; Socket: 0.05g Header: 0.03g  

^ Back to top

Material and surface treatment

Part nameMaterialSurface treatment
Molded portion LCP resin (UL94V-0) -
Contact and Post Copper alloy Contact portion: Base: Ni plating
Surface: Au plating
Terminal portion: Base: Ni plating
Surface: Au plating (except the terminal tips)

The socket terminals close to
the portion to be soldered
have nickel barriers (exposed nickel portions).

Soldering terminals: Sockets: Base: Ni
plating Surface: Pd+Au flash plating
(except the terminal tips)

Headers: Base: Ni plating
Surface: Au plating (except the terminal tips)

^ Back to top



Partners Contact Corporate International Log In