FX-300 Fiber Optic Sensors Specifications
Specifications for this product appear below.
| Type | Standard type | ||||
|---|---|---|---|---|---|
| Red LED | Blue LED | Green LED | Infrared LED | ||
| Model No. | NPN output | FX-301 | FX-301B | FX-301G | FX-301H |
| PNP output | FX-301P | FX-301BP | FX-301GP | FX-301HP | |
| Supply voltage | 12 to 24 V DC ± 10 % Ripple P-P 10 % or less | ||||
| Power consumption | Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 430 mW or less (Current consumption 18 mA or less at 24 V supply voltage) |
||||
| Output | NPN open-collector transistor ・Maximum sink current:100 mA (50 mA, if five, or more, amplifiers are connected in cascade.) ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 1.5 V or less [at 100 mA (at 50 mA, if five, or more, amplifiers are connected in cascade) sink current.] PNP open-collector transistor ・Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade.) ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 1.5 V or less [at 100 mA (at 50 mA, if five, or more, amplifiers are connected in cascade) source current.] |
||||
| Output operation | Selectable either Light-ON or Dark-ON, with jog switch | ||||
| Short-circuit protection | Incorporated | ||||
| Response time | 65 μs or less [H-SP (Red LED type only)], 150 μs or less (FAST), 250 μs or less [STD / S-D (Red LED type only)], 2 ms or less (LONG), selectable with jog switch |
||||
| Sensitivity setting | 2-level teaching / Limit teaching / Manual adjustment / Full-auto teaching / Max. sensitivity teaching |
||||
| Operation indicator | Orange LED (lights up when the output is ON) | ||||
| Stability indicator | Green LED (lights up under stable light received condition or stable dark condition) |
||||
| MODE indicator | RUN: Green LED, TEACH ・ ADJ ・ L/D ON ・ TIMER ・ PRO: Yellow LED | ||||
| Digital display | 4 digit red LED display | ||||
| Fine sensitivity adjustment function | Incorporated | ||||
| Timer function | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period: Red LED type; 0.5 ms approx., 1 to 9999 ms (Blue LED, Green LED, Infrared LED type; approx. 0.5 to 500 ms)] |
||||
| Light emitting amount selection function |
Incorporated (Red LED type only) (Note 3) FAST, STD, LONG: 4 level, H-SP: 3 level, S-D: 2 level |
||||
| Automatic interference prevention function |
Incorporated (Up to four sets of fiber heads can be mounted close together. However, H-SP mode is 2 fiber heads.) (Note 4) |
||||
| Ambient temperature | -10 to +55 ℃ +14 to -131 ℉ (If 4 to 7 units are connected in cascade: -10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are connected in cascade: -10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed), Storage: -20 to +70 ℃ - 4 to +158 ℉ | ||||
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | ||||
| Ambient illuminance | Incandescent light: 3,000 lx at the light-receiving face | ||||
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 6) | ||||
| Insulation resistance | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 6) | ||||
| Vibration resistance | 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each | ||||
| Shock resistance | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each | ||||
| Emitting element (modulated) | Red LED | Blue LED | Green LED | Infrared LED | |
| Peak emission wavelength | 650 nm 0.026 mil | 470 nm 0.019 mi | 525 nm 0.021 mil | 940 nm 0.037 mil | |
| Material | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, MODE key: Acrylic, Jog switch: Heat-resistant ABS (FX-301B/G/H: Acrylic) | ||||
| Connecting method | Connector (Note 7) | ||||
| Cable length | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | ||||
| Weight | Net weight: 20 g approx., Gross weight: 25 g approx. | ||||
| Accessory | FX-MB1 (amplifier protection seal): 1 set |
- | |||
| Type | High-speed type | High-function type | |
|---|---|---|---|
| Model No. | NPN output | FX-301-HS | FX-305 |
| PNP output | FX-301P-HS | FX-305P | |
| Supply voltage | 12 to 24 V DC ± 10 % Ripple P-P 10 % or less | ||
| Power consumption | Normal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage) ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) |
||
| Output | NPN open-collector transistor ・Maximum sink current:100 mA (50 mA, if five, or more, amplifiers are connected in cascade.) ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 1.5 V or less [at 100 mA (at 50 mA, if five, or more, amplifiers are connected in cascade) sink current.] PNP open-collector transistor ・Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade.) ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 1.5 V or less [at 100 mA (at 50 mA, if five, or more, amplifiers are connected in cascade) source current.] |
NPN open-collector transistor 2 outputs ・Maximum sink current: 50 mA each (Note 2) ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 1.5 V or less [at 50 mA (Note 2)] PNP open-collector transistor 2 outputs ・Maximum source current: 50 mA each (Note 2) ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 1.5 V or less [at 50 mA (Note 2)] |
|
| Output operation | Selectable either Light-ON or Dark-ON, with jog switch | ||
| Short-circuit protection | Incorporated | ||
| Response time | 35 μs or less (H-SP), 150 μs or less (FAST), 250 μs or less (STD / S-D), 2 ms or less (LONG), selectable with jog switch |
65 μs or less (H-SP), 150 μs or less (FAST), 250 μs or less (STD), 700 μs or less (STDF), 2.5 ms or less (LONG), 4.5 ms or less (U-LG), selectable with jog switch |
|
| Sensitivity setting | 2-level teaching / Limit teaching / Manual adjustment / Full-auto teaching / Max. sensitivity teaching |
Normal mode: 2-level teaching / Limit teaching / Full-auto teaching / Max. sensitivity teaching / Manual adjustment Window comparator mode: Teaching (1-level / 2-level / 3-level) / Manual adjustment |
|
| Operation indicator | Orange LED (lights up when the output is ON) | ||
| Stability indicator | Green LED (lights up under stable light received condition or stable dark condition) | - | |
| MODE indicator | RUN: Green LED, TEACH ・ ADJ ・ L/D ON ・ TIMER ・ PRO: Yellow LED | ||
| Digital display | 4 digit red LED display | ||
| Fine sensitivity adjustment function | Incorporated | ||
| Timer function | Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. [Timer period: Red LED type; 0.5 ms approx., 1 to 9999 ms (Blue LED, Green LED, Infrared LED type; approx. 0.5 to 500 ms)] |
Incorporated with variable ON-delay / OFF-delay / ONE SHOT / ON-delay ・ OFF-delay / ON-delay ・ ONE SHOT timer, switchable either effective or ineffective. (Timer period: Output 1; 0.5 ms, 1 to 9999 ms, Output 2; 0.5 ms, 1 to 500 ms) |
|
| Light emitting amount selection function |
Incorporated (Note 3) FAST, STD, LONG: 4 level H-SP, S-D: 2 level |
Incorporated (Note 3) FAST, STD, STDF, LONG, U-LG: 4 level H-SP: 3 level |
|
| Automatic interference prevention function |
- | Incorporated [Up to four sets of fiber heads can be mounted close together. (However, U-LG mode is 8 fiber heads, H-SP mode is 2 fiber heads.)] (Note 5) |
|
| Ambient temperature | -10 to +55 ℃ +14 to -131 ℉ (If 4 to 7 units are connected in cascade: -10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are connected in cascade: -10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed), Storage: -20 to +70 ℃ - 4 to +158 ℉ |
||
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | ||
| Ambient illuminance | Incandescent light: 3,000 lx at the light-receiving face | ||
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 6) | ||
| Insulation resistance | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 6) | ||
| Vibration resistance | 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each | ||
| Shock resistance | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each | ||
| Emitting element (modulated) | Red LED | Red LED | |
| Peak emission wavelength | 650 nm 0.026 mil | 650 nm 0.026 mil | |
| Material | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, MODE key: Acrylic, Jog switch: Heat-resistant ABS | ||
| Connecting method | Connector (Note 7) | ||
| Cable length | Total length up to 100 m 328.084 ft (50 m 164.042 ft for 5 to 8 units, 20 m 65.617 ft for 9 to 16 units) is possible with 0.3 mm2, or more, cable. | ||
| Weight | Net weight: 20 g approx., Gross weight: 25 g approx. | ||
| Accessory | - | FX-MB1 (amplifier protection seal): 1 set | |
Notes:
1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
2) 50 mA per output. 25 mA if five, or more, amplifiers are connected in cascade.
3) The light emitting amount can be zero (emission halt) in all modes.
4) When the power supply is switched on, the light emission timing is automatically set for interference prevention.
5) When the interference prevention function "1P-2 " is set, the number of mountable fiber heads becomes double.
Furthermore, take care that the response time also becomes double.
6) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
7) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cables given below.
Main cable (3-core) for FX-301(P)(-HS): CN-73-C1 (Cable length 1 m 3.281 ft), CN-73-C2 (Cable length 2 m 6.562 ft), CN-73-C5 (Cable length 5 m 16.404 ft)
Sub cable (1-core) for FX-301(P)(-HS): CN-71-C1 (Cable length 1 m 3.281 ft), CN-71-C2 (Cable length 2 m 6.562 ft), CN-71-C5 (Cable length 5 m 16.404 ft)
Main cable (4-core) for FX-305(P): CN-74-C1 (Cable length 1 m 3.281 ft), CN-74-C2 (Cable length 2 m 6.562 ft), CN-74-C5 (Cable length 5 m 16.404 ft)
Sub cable (2-core) for FX-305(P): CN-72-C1 (Cable length 1 m 3.281 ft), CN-72-C2 (Cable length 2 m 6.562 ft), CN-72-C5 (Cable length 5 m 16.404 ft)
| Type | NPN output | |||
|---|---|---|---|---|
| Red LED | Blue LED | Green LED | ||
| Model No. | FX-311 | FX-311B | FX-311G | |
| Supply voltage | 12 to 24 V DC ± 10 % Ripple P-P 10 % or less | |||
| Power consumption | 840 mW or less (Current consumption 35 mA or less at 24 V supply voltage) |
|||
| Output | NPN open-collector transistor ・Maximum sink current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) ・Applied voltage: 30 V DC or less (between output and 0 V) ・Residual voltage: 1.5 V or less at 100 mA sink current (50 mA, if five, or more, amplifiers are connected in cascade) |
|||
| Utilization category | DC-12 or DC-13 | |||
| Output operation | Selectable either Light-ON or Dark-ON, with selection switch | |||
| Short-circuit protection | Incorporated | |||
| Response time | 250 μs or less (STD / S-D), 2 ms or less (LONG) selectable with selection switch 150 μs or less (FAST), 250 μs or less (STD), 2 ms or less (LONG) selectable with selection switch |
|||
| Operation indicator | Orange LED (lights up when the output is ON) | |||
| Stability indicator | Green LED (lights up under stable light received condition or stable dark condition) |
|||
| Sensitivity adjuster | 12-turn potentiometer with indicator (Pointer part: red backlight) (Note 2) |
|||
| Timer function | Incorporated with OFF-delay timer, selectable either effective (approx. 10 ms or 40 ms) or ineffective | |||
| Automatic interference prevention function | Incorporated (Up to 4 sets of fiber heads can be mounted close together.) (Note 3) |
|||
| Pollution degree | 3 (Industrial environment) | |||
| Ambient temperature | -10 to +55 ℃ -14 to +131 ℉ (If 4 to 7 units are connected in cascade: -10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are connected in cascade: -10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed), Storage: -20 to +70 ℃ -4 to +158 ℉ |
|||
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | |||
| Ambient illuminance | Incandescent light: 3,000 lx at the light-receiving face | |||
| EMC | EN 60947-5-2 | |||
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 4) | |||
| Insulation resistance | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 4) | |||
| Vibration resistance | 10 to 150 Hz frequency, 0.75 mm 0.03 in amplitude in X, Y and Z directions for two hours each | |||
| Shock resistance | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each | |||
| Emitting element (modulated) |
Red LED | Blue LED | Green LED | |
| Peak emission wavelength | 650 nm 0.026 mil | 470 nm 0.019 mil | 525 nm 0.021 mil | |
| Material | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | |||
| Connecting method | Connector (Note 5) | |||
| Cable length | Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. | |||
| Weight | Net weight: 15 g approx., Gross weight: 20 g approx. | |||
| Type | PNP output | |||
|---|---|---|---|---|
| Red LED | Blue LED | Green LED | ||
| Model No. | FX-311P | FX-311BP | FX-311GP | |
| Supply voltage | 12 to 24 V DC ± 10 % Ripple P-P 10 % or less | |||
| Power consumption | 840 mW or less (Current consumption 35 mA or less at 24 V supply voltage) |
|||
| Output | PNP open-collector transistor ・Maximum source current: 100 mA (50 mA, if five, or more, amplifiers are connected in cascade) ・Applied voltage: 30 V DC or less (between output and +V) ・Residual voltage: 1.5 V or less at 100 mA source current (50 mA, if five, or more, amplifiers are connected in cascade) |
|||
| Utilization category | DC-12 or DC-13 | |||
| Output operation | Selectable either Light-ON or Dark-ON, with selection switch | |||
| Short-circuit protection | Incorporated | |||
| Response time | 250 μs or less (STD / S-D), 2 ms or less (LONG) selectable with selection switch 150 μs or less (FAST), 250 μs or less (STD), 2 ms or less (LONG) selectable with selection switch |
|||
| Operation indicator | Orange LED (lights up when the output is ON) | |||
| Stability indicator | Green LED (lights up under stable light received condition or stable dark condition) |
|||
| Sensitivity adjuster | 12-turn potentiometer with indicator (Pointer part: red backlight) (Note 2) |
|||
| Timer function | Incorporated with OFF-delay timer, selectable either effective (approx. 10 ms or 40 ms) or ineffective | |||
| Automatic interference prevention function | Incorporated (Up to 4 sets of fiber heads can be mounted close together.) (Note 3) |
|||
| Pollution degree | 3 (Industrial environment) | |||
| Ambient temperature | -10 to +55 ℃ -14 to +131 ℉ (If 4 to 7 units are connected in cascade: -10 to +50 ℃ +14 to +122 ℉, if 8 to 16 units are connected in cascade: -10 to +45 ℃ +14 to +113 ℉) (No dew condensation or icing allowed), Storage: -20 to +70 ℃ -4 to +158 ℉ |
|||
| Ambient humidity | 35 to 85 % RH, Storage: 35 to 85 % RH | |||
| Ambient illuminance | Incandescent light: 3,000 lx at the light-receiving face | |||
| EMC | EN 60947-5-2 | |||
| Voltage withstandability | 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 4) | |||
| Insulation resistance | 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 4) | |||
| Vibration resistance | 10 to 150 Hz frequency, 0.75 mm 0.03 in amplitude in X, Y and Z directions for two hours each | |||
| Shock resistance | 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each | |||
| Emitting element (modulated) |
Red LED | Blue LED | Green LED | |
| Peak emission wavelength | 650 nm 0.026 mil | 470 nm 0.019 mil | 525 nm 0.021 mil | |
| Material | Enclosure: Heat-resistant ABS, Case cover: Polycarbonate | |||
| Connecting method | Connector (Note 5) | |||
| Cable length | Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. | |||
| Weight | Net weight: 15 g approx., Gross weight: 20 g approx. | |||
Notes:
1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 ℃ +73.4 ℉.
2) The red backlight of the pointer part lights up more brightly when the power is turned ON and when the sensitivity is adjusted.
3) When the power supply is switched on, the emission timing are automatically set for interference prevention.
4) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
5) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cable given below.
Main cable (3-core): CN-73-C1 (cable length 1 m 3.281 ft), CN-73-C2 (cable length 2 m 6.562 ft), CN-73-C5 (cable length 5 m 16.404 ft)
Sub cable (1-core): CN-71-C1 (cable length 1 m 3.281 ft), CN-71-C2 (cable length 2 m 6.562 ft), CN-71-C5 (cable length 5 m 16.404 ft)
